Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester

Mahantesh Shivashimpi; Sidramappa Alur; Nagaraj Banapurmath; Uday Kapale

doi:doi:10.11648/j.ijctc.20190701.20

| Peer-Reviewed

Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester

Mahantesh Shivashimpi, Sidramappa Alur, Nagaraj Banapurmath, Uday Kapale

Published in International Journal of Computational and Theoretical Chemistry (Volume 7, Issue 1)

Received: 21 March 2019 Accepted: 28 April 2019 Published: 26 May 2019

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

In this investigation, the common rail direct injection (CRDI) single cylinder four stroke diesel engine has made to modify in terms of toroidal reentrant combustion chamber (TRCC) shape and 7 holes CRDI nozzle injector. The current experimental study objective is to optimization of multiple injection strategy (MIS) in modified CRDI diesel engine powered with palm oil methyl ester (POME) B100 and diesel fuels. In the first phase of work, experiment results showed that slightly improved in brake thermal efficiency (BTE) and reduced emissions except oxides of nitrogen (NO_x) for POME fuelled engine operates under optimized MIS, fuel injection timing (IT) of -10° before top dead center (BTDC) and 600 bar injection pressure (IOP) in modified CRDI diesel engine. In the second phase of work, the performance of modified CRDI diesel engine is improved by increasing IOP from 600 bar to 900 bar at same MIS and fuel IT. The second phase of experiment results showed that percentage of increase in BTE by 2.47%, peak pressure (PP) by 13.69%, heat release rate (HRR) by 17.64%, NO_X by 11.70% and percentage of decreased in ignition delay (ID) by 29.62%, combustion duration (CD) by 13.79%, unburnt hydrocarbon (UBHC) by 19.04%, carbon monoxide (CO) by 14.28%, smoke level by 20.93% as compared to first phase of work in modified CRDI diesel engine fuelled with POME.

Published in	International Journal of Computational and Theoretical Chemistry (Volume 7, Issue 1)
DOI	10.11648/j.ijctc.20190701.20
Page(s)	87-99
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2019. Published by Science Publishing Group

Keywords

Palm Oil Methyl Ester, Common Rail Direct Injection, Toroidal Reentrant Shape, Multiple Injection Strategy, Injection Timing, Injection Pressure

References

[1]	S. Jaichandar, K Annamalai, “Jatropha oil methyl ester as diesel engine fuel - an experimental investigation,” International Journal of Automotive and Mechanical Engineering, 13 (2006) 3248-3261.
[2]	F. Sundus, H. H. Masjuki, M. A. Fazal, “Analysis of tribological properties of palm biodiesel and oxidized biodiesel blends,” Tribology Transactions, 60 (2017) 530-536.
[3]	Zuhaira Abdullah, HazrulzurinaSuhaimi, Adam Abdullah, MohdFirdausTaufik, G. Anes Mrwan, “Effect of pentanol-diesel fuel blends on thermo-physical properties, combustion characteristics, engine performance and emissions of a diesel engine,” International Journal of Automotive and Mechanical Engineering, 15 (2018) 5435-5450.
[4]	S. N. Naik, V. Vaibhav, K. Goud Prashant, Rout Ajay, K. Dalai, “Production of first and second generation biofuels a comprehensive review,” Renewable and Sustainable Energy Reviews, 14 (2010) 578-597.
[5]	M. N. Mohiddin, A. A. Saleh, ANR Reddy, S. Hamdan, “A study on chicken fat as an alternative feedstock: biodiesel production, fuel Characterization and diesel engine performance analysis,” International Journal of Automotive and Mechanical Engineering, 15 (2018) 5535-5546.
[6]	M. Mani, G. Nagarajan, S. Sampath, “Characterization and effect of using waste plastic oil and diesel fuel blends in compression ignition engine,” Energy, 36 (2011) 212-219.
[7]	A. Atmanli, E. Ileri, B. Yuksel, “Experimental investigation of engine performance and exhaust emissions of a diesel engine fueled with diesel-n-butanol vegetable oil blends,” Energy Conversion Management, 81 (2014) 312-21.
[8]	A. T. Hoang, M. M. Noorand, X. D. Pham, “Comparative analysis on performance and emission Characteristic of diesel engine fueled with heated coconut oil and diesel Fuel, ”International Journal of Automotive and Mechanical Engineering, 15 (2018) 5110-5125.
[9]	A. Gautam, A. K. Agarwal, “Experimental investigations of comparative performance, emission and combustion characteristics of cotton seed biodiesel-fueled four-stroke locomotive diesel engine,” International Journal of Engine Research, 14 (2013) 354–72.
[10]	S. Dixit, A. Rehman, “Linseed oil as a potential resource for bio-diesel: a review,” Renewable Sustainable Energy Reviews, 16 (2012) 4415-21.
[11]	D. Kannan, S. Pachamuthu, N. M. Nurun, J. E. Hustad, T. Lovas, “Theoretical and experimental investigation of diesel engine performance, combustion and emissions analysis fuelled with the blends of ethanol, diesel and jatropha methyl ester,” Energy Conversion Management, 53 (2012) 322-331.
[12]	G. Venkata Subbaiah, K. Raja Gopal, “An experimental investigation on the performance and emission characteristics of a diesel engine fuelled with rice brain biodiesel and ethanol blends,” Green Energy, 8 (2011) 197-208.
[13]	Abhishek Sharma, S. Murugan, “Investigation on the behavior of a DI diesel engine fuelled with jatropha methyl ester (JME) and tyre pyrolysis Oil (TPO) blends,” Fuel, 108 (2013) 699-708.
[14]	Aydin, Huseyin, CumaliLlkılıc, “Analysis of combustion, performance and emission characteristics of a diesel engine using low sulfur tire fuel,” Fuel, 143 (2015) 373-82.
[15]	K. Bhaskar, S. Sendilvelan, “Experimental studies on the performance and emission characteristics of a compression ignition engine fuelled with jatropha oil methyl ester,” Journal of Mechanical Engineering and Sciences, 12 (2018) 3431-3450.
[16]	M. M. Roy, “Effect of fuel injection timing and injection pressure on combustion and odorous emissions in DI diesel engine,” Energy Resources Technology, 131 (2009) 1-8.
[17]	S. Bari, C. H. Yu, T. H. Lim, “Effect of fuel injection timing with waste cooking oil as a fuel in direct injection diesel engine,” Proceedings of the Institution of Mechanical Engineers, Part D, Journal of Automobile Engineering, 218 (2004) 93-104.
[18]	N. R. Banapurmath, P. G. Tewari, V. N. Gaitonde, “Experimental investigations on performance and emission characteristics of Honge oil biodiesel (HOME) operated compression ignition engine,” Renewable Energy, 48 (2012) 193-201.
[19]	Abhishek Sharma, S. Murugan, “Combustion, performance and emission characteristics of a DI diesel engine fuelled with non-petroleum fuel: A study on the role of fuel injection timing,” Energy Institute, 88 (2015) 364-75.
[20]	G. Suresh, H. C. Kamath, N. R. Banapurmath, "Effect of injection timing, injector opening pressure and nozzle geometry on the performance of cotton seed oil methyl ester fuelled diesel engine,” Sustainable Engineering, 7 (2013) 82-92.
[21]	S. Rostami, B. Ghobadian, M. Kiani Deh Kiani, “Effect of the injection timing on the performance of a diesel engine using diesel-biodiesel blends,” International Journal of Automotive and Mechanical Engineering, 10 (2014) 1945-1958.
[22]	Karra, K. Prashanth, Song Charng Kong, “Experimental study on effects of nozzle holes geometry on achieving low diesel engine emissions,”Engineering for Gas Turbines and Power, 132 (2010) 022802.
[23]	Lahane, Subhash, K. A. Subramanian, “Impact of nozzle holes configuration on fuel spray, wall impingement and NO_x emission of a diesel engine for biodiesel–diesel blend (B20),”Applied Thermal Engineering, 64 (2014) 307-314.
[24]	S. V. Khandal, N. R. Banapurmath, V. N. Gaitonde, R. S. Hosmath, “Effect of number of injector nozzle holes on the performance, emission and combustion characteristics of honge oil biodiesel (HOME) Operated DI compression Ignition Engine,” Petroleum and Environmental Biotechnology, 6 (2015) 1-18.
[25]	S. P. Wategave, M. S. Sawant, M. S. Tandale, G. Suresh, V. S. Yaliwalc, N. R. Banapurmath, P. G. Tewari, “Effect of injection timing, injector opening pressure and nozzle geometry on the performance of a compression ignition engine operated on non-edible oil methyl esters from different sources,” Sustainable Engineering, 1 (2014) 71-81.
[26]	S. Jaichandar, K. Annamalai, “Effects of open combustion chamber geometries on the performance of pongamia biodiesel in a DI diesel engine,” Fuel, 98 (2012) 272–279.
[27]	S. Jaichandar S, K. Annamalai, “Combined impact of injection pressure and combustion chamber geometry on the performance of a biodiesel fueled diesel engine,” Energy, 55 (2013) 330-339.
[28]	N. R. Banapurmath, A. S. Chavan, S. B. Bansode, Sankalp Patil, G. Naveen, Sanketh Tonannavar, N. K. Keerthi, M. S. Tandale, “Effect of combustion chamber shapes on the performance of mahua and neem biodiesel operated diesel engine,” Petroleum and Environmental Biotechnology, 6 (2015) 1-7.
[29]	MahanteshM. Shivashimpi, S. A. Alur, S. N. Topannavar, B. M. Dodamani, “Combined effect of cylindrical combustion chamber shape and nozzle geometry on the performance and emission characteristics of C.I. engine operated on pongemia,” Mechanical engineering for sustainable development state of the art research, USA: Apple Academic Press, CRC press, Taylor and Francis Group, (2018) 345-359.
[30]	MahanteshM. Shivashimpi, S. A. Alur, S. N. Topannavar, B. M. Dodamani, “Combined effect of combustion chamber shapes and nozzle geometry on the performance and emission characteristics of C.I. engine operated on Pongamia,” Energy, 154 (2018) 17-26.
[31]	Mobasheri, Raouf, ZhijunPeng, “CFD investigation of the effects of re-entrant combustion chamber geometry in a HSDI diesel engine,” Scientific Research Innovation, 7 (2013) 770-780.
[32]	S. Jaichandar, P. Senthil Kumar, K. Annamalai, “Combined effect of injection timing and combustion chamber geometry on the performance of a biodiesel fueled diesel engine,” Energy, 47.1 (2012) 388-394.
[33]	V. S. Yaliwal, N. R. Banapurmath, N. M. Gireesh, R. S. Hosmath, Teresa Donateo, P. G. Tewari, “Effect of nozzle and combustion chamber geometry on the performance of a diesel engine operated on dual fuel mode using renewable fuels,” Renewable Energy, 93 (2016) 483-501.
[34]	Venkata Ramesh Mamilla, M. V. Mallikarjun, G. Lakshmi NarayanaRao, “Effect of combustion chamber design on a DI diesel engine fuelled with jatropha methyl esters blends with diesel,” Procedia Engineering, 64 (2013) 479-490.
[35]	Vinay Kumar, “Experimental investigation of piston bowl geometry effects on performance and emissions characteristics of diesel engine at variable injection pressure and timings,” Ambient Energy, 39 (2018) 685-693.
[36]	M. M. Shivashimpi, N. R. Banapurmath, S. A. Alur, S. V. Khandal, “Effect of combustion chamber shapes, nozzle holes geometries, injection pressures and injection timing on the performance diesel engine fueled with palm oil methyl ester,” European Journal of Sustainable Development Research, 2 (2018) 1-17.
[37]	SrinathPai, Abdul Sharief, Shiva Kumar, “Influence of ultra injection pressure with dynamic injection timing on CRDI engine performance using simarouba biodiesel blends,” International Journal of Automotive and Mechanical Engineering, 15 (2018) 5748-5759.
[38]	D. H. Qi, K. Yang, D. Zhang, B. Chen, Q. Wei, C. H. Zhang, “Experimental investigation of a turbocharged CRDI diesel engine fueled with tung oil-diesel-ethanol micro emulsion fuel,” Renewable Energy, 113 (2017) 1201-1207.
[39]	C. Syed Aalam, C. G. Saravanan, B. Prem Anand, “Impact of high fuel injection pressure on the characteristics of CRDI diesel engine powered by mahua methyl ester blend,” Applied Thermal Engineering, 106 (2016) 702–711.
[40]	S. V. Khandal, N. R. Banapurmath, V. N. Gaitonde, V. S. Yaliwal, “Common rail direct injection mode of CI engine operation with different injection strategies - a method to reduce smoke and NO_x emissions simultaneously," European Journal of Sustainable Development Research, 2 (2018) 1-18.
[41]	S. Karthikeyan, T. Dharma Prabhakaran, A. Prathima, “Environment effect of La2O3 nano-additives on microalgae-biodiesel fueled CRDI engine with conventional diesel,” Energy Sources Part A: Recovery Utilization and Environmental Effects, 40 (2018) 179-185.
[42]	D. I. Silvana Iorio, Ezio Mancaruso, M. Bianca Vaglieco, “Characterization of soot particles produced in a transparent research CRDI diesel engine operating with conventional and advanced combustion strategies,” Aerosol Science and Technology, 46 (2012) 272-286.
[43]	Shukla, A. D. Shetty, A. J. Antony, “Performance and emission characteristics of CRDI engine working on plastic oil,” Indian journal of science and technology, 9 (2016) 1-6.
[44]	Avinash Kumar Agarwal, AtulDhar, Jai Gopal Gupta, WoongKim, Kibong Choi, Chang Sik Lee, Sungwook Park, “Effect of fuel injection pressure and injection timing of Karanja biodiesel blends on fuel spray, engine performance, emissions and combustion characteristics,” Energy Conversion and Management, 91 (2015) 302-314.
[45]	Avinash Kumar Agarwal, AtulDhar, Jai Gopal Gupta, WoongKim, Chang Sik Lee, SungwookPark, “Effect of fuel injection pressure and injection timing on spray characteristics and particulate size–number distribution in a biodiesel fuelled common rail direct injection diesel engine,” Applied Energy, 130 (2014) 212-221.
[46]	D. H. Qi, K. Yang, D. Zhang, B. Chen, “Combustion and emission characteristics of diesel-tung oil-ethanol blended fuels used in a CRDI diesel engine with different injection strategies,” Applied Thermal Engineering, 111 (2017) 927–935.
[47]	AtulDhar, Avinash Kumar Agarwal, “Experimental investigations of the effect of pilot injection on performance, emissions and combustion characteristics of Karanja biodiesel fuelled CRDI engine,” Energy Conversion and Management, 93 (2015) 357-366.
[48]	M. Mikulski, K. Duda, S. Wierzbicki, “Performance and emissions of a CRDI diesel engine fuelled with swine lard methyl esters-diesel mixture,” Fuel, 164 (2016) 206-219.
[49]	Khairul Azly Zahan, Manabu Kano, “Biodiesel production from palm oil, its by-products, and mill effluent: a review,” Journal of Energies 11 (2018) 1-25.
[50]	S. O. Kareem, E. I. Falokun, S. A. Balogun, O. A. Akinloye, S. O. Omeike, “Enzymatic biodiesel production from palm oil and palm kernel oil using free lipase,” Egyptian Journal of Petroleum, 26 (2017) 635-642.
[51]	S. Kevin Chen, “Simultaneous reduction of NO_x and particulate emissions by using multiple injections in a small diesel engine,” SAE, 01 (2000) 1-10.
[52]	B. P. Pattanaik, J. Jena, R. D. Misra, “The effect of oxygen content in soapnut biodiesel-diesel blends on performance of a diesel engine,” International Journal of Automotive and Mechanical Engineering, 14 (2017) 4574-4588.
[53]	M. Mikulski, k. Duda, S. Wierzbicki, “Performance and emissions of a CRDI diesel engine fuelled with swine lard methyl esters-diesel mixture,”Fuel, 164 (2016) 206-219.
[54]	C. S. Lee, S. W. Park, “An experimental and numerical study on fuel atomization characteristics of high pressure diesel injection sprays,” Fuel, 81 (2002) 2417-2423.
[55]	N. M. Taib, M. S. Zainuddin, MRA. Mansor, Z. Ilham, “Performance and emission opacity of canola and soybean biodiesel fuel in a diesel engine,” Journal of Mechanical Engineering and Sciences, 12 (2018) 3689-369.
[56]	V. Khalid, ASA. Tajuddin, N. Jaat, B. Manshoor, I. Zaman, SAA. Hadi, R. S. Nursal, “Performance and emissions of diesel engine fuelled with preheated biodiesel fuel derived from crude palm, jatropha, and waste cooking oils,” International Journal of Automotive and Mechanical Engineering, 14 (2017) 4273-4284.
[57]	NorrizamJaat, Amir Khalid, Mariam Basharie, Azahari Razali, Azwan Sapit, Z. Noranai, “Influences of the end of injection and ambient temperature on biodiesel combustion, ”Journal of Mechanical Engineering and Sciences, 11 (2017) 2883-2994.

Cite This Article

Plain Text BibTeX RIS

APA Style

Mahantesh Shivashimpi, Sidramappa Alur, Nagaraj Banapurmath, Uday Kapale. (2019). Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester. International Journal of Computational and Theoretical Chemistry, 7(1), 87-99. https://doi.org/10.11648/j.ijctc.20190701.20

Copy | Download

ACS Style

Mahantesh Shivashimpi; Sidramappa Alur; Nagaraj Banapurmath; Uday Kapale. Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester. Int. J. Comput. Theor. Chem. 2019, 7(1), 87-99. doi: 10.11648/j.ijctc.20190701.20

Copy | Download

AMA Style

Mahantesh Shivashimpi, Sidramappa Alur, Nagaraj Banapurmath, Uday Kapale. Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester. Int J Comput Theor Chem. 2019;7(1):87-99. doi: 10.11648/j.ijctc.20190701.20

Copy | Download

@article{10.11648/j.ijctc.20190701.20,
  author = {Mahantesh Shivashimpi and Sidramappa Alur and Nagaraj Banapurmath and Uday Kapale},
  title = {Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester},
  journal = {International Journal of Computational and Theoretical Chemistry},
  volume = {7},
  number = {1},
  pages = {87-99},
  doi = {10.11648/j.ijctc.20190701.20},
  url = {https://doi.org/10.11648/j.ijctc.20190701.20},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijctc.20190701.20},
  abstract = {In this investigation, the common rail direct injection (CRDI) single cylinder four stroke diesel engine has made to modify in terms of toroidal reentrant combustion chamber (TRCC) shape and 7 holes CRDI nozzle injector. The current experimental study objective is to optimization of multiple injection strategy (MIS) in modified CRDI diesel engine powered with palm oil methyl ester (POME) B100 and diesel fuels. In the first phase of work, experiment results showed that slightly improved in brake thermal efficiency (BTE) and reduced emissions except oxides of nitrogen (NOx) for POME fuelled engine operates under optimized MIS, fuel injection timing (IT) of -10° before top dead center (BTDC) and 600 bar injection pressure (IOP) in modified CRDI diesel engine. In the second phase of work, the performance of modified CRDI diesel engine is improved by increasing IOP from 600 bar to 900 bar at same MIS and fuel IT. The second phase of experiment results showed that percentage of increase in BTE by 2.47%, peak pressure (PP) by 13.69%, heat release rate (HRR) by 17.64%, NOX by 11.70% and percentage of decreased in ignition delay (ID) by 29.62%, combustion duration (CD) by 13.79%, unburnt hydrocarbon (UBHC) by 19.04%, carbon monoxide (CO) by 14.28%, smoke level by 20.93% as compared to first phase of work in modified CRDI diesel engine fuelled with POME.},
 year = {2019}
}

Copy | Download

TY  - JOUR
T1  - Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester
AU  - Mahantesh Shivashimpi
AU  - Sidramappa Alur
AU  - Nagaraj Banapurmath
AU  - Uday Kapale
Y1  - 2019/05/26
PY  - 2019
N1  - https://doi.org/10.11648/j.ijctc.20190701.20
DO  - 10.11648/j.ijctc.20190701.20
T2  - International Journal of Computational and Theoretical Chemistry
JF  - International Journal of Computational and Theoretical Chemistry
JO  - International Journal of Computational and Theoretical Chemistry
SP  - 87
EP  - 99
PB  - Science Publishing Group
SN  - 2376-7308
UR  - https://doi.org/10.11648/j.ijctc.20190701.20
AB  - In this investigation, the common rail direct injection (CRDI) single cylinder four stroke diesel engine has made to modify in terms of toroidal reentrant combustion chamber (TRCC) shape and 7 holes CRDI nozzle injector. The current experimental study objective is to optimization of multiple injection strategy (MIS) in modified CRDI diesel engine powered with palm oil methyl ester (POME) B100 and diesel fuels. In the first phase of work, experiment results showed that slightly improved in brake thermal efficiency (BTE) and reduced emissions except oxides of nitrogen (NOx) for POME fuelled engine operates under optimized MIS, fuel injection timing (IT) of -10° before top dead center (BTDC) and 600 bar injection pressure (IOP) in modified CRDI diesel engine. In the second phase of work, the performance of modified CRDI diesel engine is improved by increasing IOP from 600 bar to 900 bar at same MIS and fuel IT. The second phase of experiment results showed that percentage of increase in BTE by 2.47%, peak pressure (PP) by 13.69%, heat release rate (HRR) by 17.64%, NOX by 11.70% and percentage of decreased in ignition delay (ID) by 29.62%, combustion duration (CD) by 13.79%, unburnt hydrocarbon (UBHC) by 19.04%, carbon monoxide (CO) by 14.28%, smoke level by 20.93% as compared to first phase of work in modified CRDI diesel engine fuelled with POME.
VL  - 7
IS  - 1
ER  -

Copy | Download

Author Information

Mahantesh Shivashimpi

Mechanical Engineering, Hirasugar Institute of Technology, Nidasoshi, Karnataka, India
Sidramappa Alur

Mechanical Engineering, Hirasugar Institute of Technology, Nidasoshi, Karnataka, India
Nagaraj Banapurmath

Department of Mechanical Engineering, B. V. Bhoomaraddi College of Engineering and Technology, Hubballi, Karnataka, India
Uday Kapale

Mechanical Engineering, S. G. Balekundri Institute of Technology, Belagavi, Karnataka, India

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Mahantesh Shivashimpi, Sidramappa Alur, Nagaraj Banapurmath, Uday Kapale. (2019). Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester. International Journal of Computational and Theoretical Chemistry, 7(1), 87-99. https://doi.org/10.11648/j.ijctc.20190701.20

Copy | Download

ACS Style

Mahantesh Shivashimpi; Sidramappa Alur; Nagaraj Banapurmath; Uday Kapale. Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester. Int. J. Comput. Theor. Chem. 2019, 7(1), 87-99. doi: 10.11648/j.ijctc.20190701.20

Copy | Download

AMA Style

Mahantesh Shivashimpi, Sidramappa Alur, Nagaraj Banapurmath, Uday Kapale. Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester. Int J Comput Theor Chem. 2019;7(1):87-99. doi: 10.11648/j.ijctc.20190701.20

Copy | Download

@article{10.11648/j.ijctc.20190701.20,
  author = {Mahantesh Shivashimpi and Sidramappa Alur and Nagaraj Banapurmath and Uday Kapale},
  title = {Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester},
  journal = {International Journal of Computational and Theoretical Chemistry},
  volume = {7},
  number = {1},
  pages = {87-99},
  doi = {10.11648/j.ijctc.20190701.20},
  url = {https://doi.org/10.11648/j.ijctc.20190701.20},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijctc.20190701.20},
  abstract = {In this investigation, the common rail direct injection (CRDI) single cylinder four stroke diesel engine has made to modify in terms of toroidal reentrant combustion chamber (TRCC) shape and 7 holes CRDI nozzle injector. The current experimental study objective is to optimization of multiple injection strategy (MIS) in modified CRDI diesel engine powered with palm oil methyl ester (POME) B100 and diesel fuels. In the first phase of work, experiment results showed that slightly improved in brake thermal efficiency (BTE) and reduced emissions except oxides of nitrogen (NOx) for POME fuelled engine operates under optimized MIS, fuel injection timing (IT) of -10° before top dead center (BTDC) and 600 bar injection pressure (IOP) in modified CRDI diesel engine. In the second phase of work, the performance of modified CRDI diesel engine is improved by increasing IOP from 600 bar to 900 bar at same MIS and fuel IT. The second phase of experiment results showed that percentage of increase in BTE by 2.47%, peak pressure (PP) by 13.69%, heat release rate (HRR) by 17.64%, NOX by 11.70% and percentage of decreased in ignition delay (ID) by 29.62%, combustion duration (CD) by 13.79%, unburnt hydrocarbon (UBHC) by 19.04%, carbon monoxide (CO) by 14.28%, smoke level by 20.93% as compared to first phase of work in modified CRDI diesel engine fuelled with POME.},
 year = {2019}
}

Copy | Download

TY  - JOUR
T1  - Optimization of Multiple Injection Strategy in Modified Common Rail Direct Injection Diesel Engine Powered with Palm Oil Methyl Ester
AU  - Mahantesh Shivashimpi
AU  - Sidramappa Alur
AU  - Nagaraj Banapurmath
AU  - Uday Kapale
Y1  - 2019/05/26
PY  - 2019
N1  - https://doi.org/10.11648/j.ijctc.20190701.20
DO  - 10.11648/j.ijctc.20190701.20
T2  - International Journal of Computational and Theoretical Chemistry
JF  - International Journal of Computational and Theoretical Chemistry
JO  - International Journal of Computational and Theoretical Chemistry
SP  - 87
EP  - 99
PB  - Science Publishing Group
SN  - 2376-7308
UR  - https://doi.org/10.11648/j.ijctc.20190701.20
AB  - In this investigation, the common rail direct injection (CRDI) single cylinder four stroke diesel engine has made to modify in terms of toroidal reentrant combustion chamber (TRCC) shape and 7 holes CRDI nozzle injector. The current experimental study objective is to optimization of multiple injection strategy (MIS) in modified CRDI diesel engine powered with palm oil methyl ester (POME) B100 and diesel fuels. In the first phase of work, experiment results showed that slightly improved in brake thermal efficiency (BTE) and reduced emissions except oxides of nitrogen (NOx) for POME fuelled engine operates under optimized MIS, fuel injection timing (IT) of -10° before top dead center (BTDC) and 600 bar injection pressure (IOP) in modified CRDI diesel engine. In the second phase of work, the performance of modified CRDI diesel engine is improved by increasing IOP from 600 bar to 900 bar at same MIS and fuel IT. The second phase of experiment results showed that percentage of increase in BTE by 2.47%, peak pressure (PP) by 13.69%, heat release rate (HRR) by 17.64%, NOX by 11.70% and percentage of decreased in ignition delay (ID) by 29.62%, combustion duration (CD) by 13.79%, unburnt hydrocarbon (UBHC) by 19.04%, carbon monoxide (CO) by 14.28%, smoke level by 20.93% as compared to first phase of work in modified CRDI diesel engine fuelled with POME.
VL  - 7
IS  - 1
ER  -

Copy | Download